Correct 1/2 Wheel Stud for Dexter 7K Axle

Question

Question:

Is there a way to interchange an AL-KO part# 1530093 to a Dexter wheel stud part number? It is for a Dexter 7K Axle as shown in the attached images.

asked by: Anonymous

0

Expert Reply:

The correct wheel stud for a Dexter 7K Axle with 1/2" Wheel Studs is the Dexter Wheel Bolt part # 7-262 which is cross-compatible with the AL-KO 1530093.

expert reply by: Conner L

0

Correct 1/2" Wheel Stud for Dexter 7K Axle
(click to enlarge)

Answer 1

We have lots of slide out parts available, however I need to know which part you are looking for. If you can provide me with the serial numbers and which parts you are looking for I can make a recommendation. You can typically find the serial number…

view full answer...

Answer 2

The trailer hub part #AKIHUB-865-7-1-K does fit the Timbren Axle-Less Trailer Suspension System #TASR7KS01 that you mentioned. Then when you want to use a slip on disc brake kit you'd want the part #K2R79D which will fit and work well with this…

view full answer...

Answer 3

The replacement studs for the trailer hub #8-231-9UC1-EZ are part number #7-262 which overall are 2.7 inches but would stick through the hub 1-1/4 inches past the mounting flange of it.

view full answer...

Answer 4

Thanks for the picture of your wheel and valve stem setup. I'd recommend 135 degree valve extenders like the part #WM8029135 as this will put the valve stem at a better angle than a 180 degree kit. These will work great with your current wheel…

view full answer...

Answer 5

So there could be a number of different issues behind why your Dexter Nev-R-Adjust Electric Trailer Brake Kit #23-468-469 feel weak. First, let's start with the more obvious, which is the wiring, specifically, a ground that is loose or weak from…

view full answer...

Answer 6

The closest wheel stud we offer to what you need is the part #RG03-040. This has a 1/2 inch thread diameter, .61 spline diameter, overall length of 1.8125 inches. It matches your stud very closely.

view full answer...

Answer 7

Sometimes with all the studs of a hub sheer off it's because one lug nut started to come loose which then caused others to work loose and with enough play the impact on the stud as the wheel turns eventually sheers off the stud. The replacement…

view full answer...

Answer 8

In order to find which MORryde Suspension Upgrade Kit fits your 2022 XLR Nitro 28DK5 you will need to measure the length of your shackle straps. This is the center of hole to center of hole measurement. If you find that you have 2-1/4" shackles…

view full answer...

Answer 9

Thanks for the picture and info on your current brake assemblies, from that we know that the Dexter brake assembly part #23-106 that you referenced is the correct fit. For the left hand side you'd then want the part #23-105.

view full answer...

Answer 10

You can't use conical/tapered lug nuts like the #12CLN on wheels with flat bolt seats; instead you'll want to use a lug nut with a flange like the Flange Wheel Nut - 5/8" #95188. If you can tell me which wheels you've got and the lug…

view full answer...

Answer 11

In order to use 17.5" diameter trailer wheels you'll need to upgrade to 9/16" lug studs. There are no other options as all wheels this size use this size or larger since they are designed for more weight. In order to do this you'll…

view full answer...

Answer 12

I checked with Dexter and was able to verify the correct studs for the Dexter Trailer Hub and Drum 42656. Per Dexter the correct replacement is the 2" long stud, which is the following part number: - Trailer Hub Wheel Stud - Drive In - 1/2"…

view full answer...

Correct 1/2 Wheel Stud for Dexter 7K Axle

Product Page this Question was Asked From

Continue Researching