Conventional Ramp Door Spring that Fits 61 inch Wide Ramp Door

Question

Question:

My front ramp door is 61” wide, how much is the cost to cut down ?

asked by: Bob

0

Expert Reply:

We don't have ability to cut down our trailer ramp springs at this time but we do have a Conventional Ramp Door Spring that does fit your 61 inch wide door that would not require cutting with the part # 362SA6 which would work great.

expert reply by: Jameson C

0

Answer 1

Trailer ramp door springs are generally chosen based on the inside width of the trailer where it will be installed. Also, ramp door springs such as #362SA6 can be trimmed down some if the length is too much for the trailer. This is the shortest…

view full answer...

Answer 2

Trailer ramp spring #362SW61 could work provided that the interior of the trailer is wide enough for the rod (the rod can be trimmed down as low as 48 inches). The capacity of this spring is 120 pounds so it will help when both raising and lowering…

view full answer...

Answer 3

The Conventional Ramp Door Spring for 6' Wide Enclosed Trailer part #362SA6 can be cut down to fit a 38" wide doorway. Therefore, it would indeed work with a roughly 3-1/2' wide doorway.

view full answer...

Answer 4

Ramp springs such as #RS16933LH would be too heavy duty for your 5x8 trailer. The only other option we carry would be a garage door type of spring system. Since the trailer is 72 inches wide on the inside you would use #362SA7 which is 77 inches wide…

view full answer...

Answer 5

The best ramps spring option we have would be the part #362SA7 which is 77 inches wide and has a lifting power of 150 lbs. It can be cut down to your specific custom needs and is designed to accommodate doors as small as 43 inches in width. Warning:…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Conventional Ramp Door Spring that Fits 61 inch Wide Ramp Door

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching