Converting Swing Open Trailer Door to a Ramp Door to Load a Motorcycle
Question:
I am looking at converting a small enclosed trailer which currently has a swing door to a ramp door to make it easier to load my motorcycle. I know I will have to beef up the inside of the door for the increased weight. The door is 48inch wide. I think this spring would help with the closing of the door. Is that correct? Also, which other items would you suggest for the conversion?
asked by: Jerry K
Helpful Expert Reply:
Trailer ramp spring # 362SW61 could work provided that the interior of the trailer is wide enough for the rod (the rod can be trimmed down as low as 48 inches). The capacity of this spring is 120 pounds so it will help when both raising and lowering the door.
You really would not need additional parts other than bolts to mount it in the trailer. To strengthen the door without adding to much weight you could use aluminum beams if you can find some locally or online.
For the door itself you will need the right kind of hinge such as # SH300. This is 3 inch wide stainless steel so corrosion will not be an issue. This hinge can also be trimmed to the length needed.
I also recommend some type of retention device for the door when it is up such as # 383200 which can be used horizontally or vertically. You just need to supply your own pipe.
Products Referenced in This Question
Cam-Action Lockable Door Latch for Small Trailers and Trucks - Zinc Plated Steel
- Trailer Door Latch
- Latches
- Cam Door Latch
- Steel
- Lock Not Included
- 5-1/8 Inch Long
- 1 Inch Wide
- Polar Hardware
more information >
3" Wide Continuous Hinge - 6' Long - Stainless Steel
- Trailer Door Hinges
- Piano Hinge
- Continuous Hinge
- Stainless Steel
- 72 Inch Long
- 1/4 Inch Diameter
- 3 Inch Wide
- Bolt-On - No Pre-Drilled Holes
- Weld-On
- Polar Hardware
more information >
Continue Researching
- Shop: Cam-Action Lockable Door Latch for Small Trailers and Trucks - Zinc Plated Steel
- Shop: Ramp Door Hinge - 8-3/16" Long - 1" Pin Diameter - Steel
- Shop: 3" Wide Continuous Hinge - 6' Long - Stainless Steel
- Shop: Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers - Zinc Plated Steel
- Shop: Gooseneck Hitch
- Shop: B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs
- Video: Polar Hardware Continuous Hinge Installation
- Shop: 6" Wide Continuous Hinge - 8' Long - 1/2" Pin Diameter - Steel
- Shop: Weld-On Hinge w/ Brass Bushing and Grease Zerk - Steel - 10-1/4" Long - 3/4" Pin Diameter
- Shop: RV Exterior Lighting
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: RV Interior Lighting
- Shop: Suspension Enhancement
- Q&A: Recommendations for Converting a Barn Trailer Door to a Ramp Door
- Video: Best 2022 GMC Acadia Trailer Hitch Options
- Video: Reese Spacer Kit for Rotating Turrets Review
- Search Results: fabex 520
- Search Results: trailer door hinges
- Video: Review of TecNiq Trailer Lights - Submersible LED Backup Trailer Tail Lights - TN33XR
- Q&A: Conventional Ramp Door Spring that Fits 61 inch Wide Ramp Door
- Q&A: Ramp Door Spring Recommendation for a 2009 Carson 6x10 Enclosed Trailer
- Search Results: weatherstrip
- Video: Air Lift LoadLifter 5000 Rear Air Helper Springs Installation - 2021 GMC Sierra 1500
- Q&A: Should Enclosed Trailer Ramp Spring # 362SA6 Install to Sheet Metal Above Enclosed Trailer Ramp
- Video: Curt A16 Fifth Wheel Trailer Hitch Sidewinder Wedge Kit Review
- Video: Reese 5th Airborne 5th Wheel Air Ride King Pin with Sidewinder Review
- Search Results: 61422
- Search Results: sidewinder
- Search Results: 61300