Replacement License Plate Holder For 4 Kayak Malone MicroSport Trailer

Question

Question:

Hi. How do I add a license plate holder maybe lighted to the 4 kayak trailer.

asked by: Cliff

1

Helpful Expert Reply:

The Malone MicroSport Trailer # MPG462G2 for hauling 4 kayaks will come with a bracket like the License Plate Bracket # BK31BB. This will mount using the same hardware as the Driver's-Side LED Taillight # MAL75YR. This taillight has a light on the bottom to illuminate your license plate.

expert reply by: Bud M

1

Answer 1

Yes. You can use the Kenda #AM30030 on your Malone EcoLight trailer and they will work just fine since the hubs on the trailer are 5 on 4-1/2 bolt pattern as well. These tires have a 65 mph speed rating.

view full answer...

Answer 2

Yes, the Kenda 4.80/4.00-8 Bias Trailer Tire with 8" Galvanized Wheel - 5 on 4-1/2 #AM30030 is a substitute for the Spare Tire for Malone EcoLight Trailer #MAL33FR. Both tires are capable of being used on the Malone EcoLight Trailers #MAL53FR,…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 11

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Replacement License Plate Holder For 4 Kayak Malone MicroSport Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching