Replacement Stainless Steel Kodiak Trailer Brake Kit For 6,000LB Axle With 6 On 5-1/2 Bolt Pattern

Question

Question:

Hello ET. I have an older EZLoader boat trailer, that uses the intregal hubs the hub and rotor are one part. It has the Kodiak SS, 6on5 1/2 hubs for 15 tires on 6k# axles, but, theyre completely rusted out. Do you actually carry that kit? Let me know, please. Thank you.

asked by: Steve

0

Expert Reply:

Currently Kodiak only manufacturers the 12" Hub-and-Rotor Assembly # KHR12D with a Dacromet coating and is not available in stainless steel. They do offer their Kodiak Disc Brake Kit # K2R526S which you will be able to use with a pair of their Stainless Steel Hubs # KH42655S. This kit uses a Stainless Steel 12" Rotor # KR12S. For each braking axle you will need the following parts to replace your entire brake assemblies.

Kodiak Disc Brake Kit # K2R526S Qty 1
Stainless Steel Hub # KH42655S Qty 2
Inner Bearing # 25580 Qty 2
Outer Bearing # 15123 Qty 2
Grease Seal # GS-2250DL Qty 2
Lug Nut # KALN1375S Qty 12

expert reply by: Bud M

0

Answer 1

view full answer...

Answer 2

Starting with the axles, we do not carry any galvanized axles in the dimension you are needing. You may consider taking the axles you already have and having them galvanized at a local facility as long as they are not otherwise damaged. While we do…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Replacement Stainless Steel Kodiak Trailer Brake Kit For 6,000LB Axle With 6 On 5-1/2 Bolt Pattern

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching