Center Cap Plug Diameter for Americana Trailer Wheel Center Cap for 3.19" Pilot Hole

Question

Question:

Can you tell me what size the black center cap is for item AM90175 this cap fell out of mine

asked by: Brent

0

Expert Reply:

The black center cap of the Americana Trailer Wheel Center Cap # AM90175 is found as part # AM90081. It has a 2-1/16" outer diameter and it fits a 1-7/8" hole on the center cap.

expert reply by: Jon G

0

Answer 1

Thanks for reaching out, MikePA! The Dexter Nev-R-Adjust Electric Trailer Brakes Kit #23-468-469 only come with the brakes. For your current drums you'll want to inspect them for damage on the inside and you'll need to repack the bearings if…

view full answer...

Answer 2

Either the Americana Trailer Wheel Center Cap #AM90175 you referenced or the Trailer Wheel Center Cap #319EZ-SS would work well as a center cap for the Americana Aluminum Split Spoke Trailer Wheel #AM20440 since they both are designed for pilot…

view full answer...

Answer 3

Yes, you will have to remove your wheel to install the Americana Trailer Wheel Center Cap #AM90175. You will need to pull the wheel off and then insert the cap from the back side of the wheel. The flange and the base of the cap is what holds it in…

view full answer...

Answer 4

We do have the stainless steel Americana Trailer Wheel Center Cap #AM90175 which fits a 3.19" pilot and has an overall height of 3-3/4". I went out to the warehouse and found that the internal height is about 3-1/8" to clips on the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Center Cap Plug Diameter for Americana Trailer Wheel Center Cap for 3.19" Pilot Hole

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching