Recommended 7-Way Connector for a 2022 Toyota Tacoma

Question

Question:

I am getting the Curt 5639 4 pole wiring kit for my 2022 Tacoma - what do I want to get for the 7 pole that will fit in a Toyota OEM wiring harness connector?

asked by: Ryan

0

Expert Reply:

To add a 7-way connector to your 2022 Toyota Tacoma you will want the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter item # 22117. This custom-fit T-One connector plugs into your Tacoma's wiring harness, which is located behind the driver's-side and passenger's-side tail lights.

This 7-way connector will not work with the Curt item # C56349. They install in the same location.

If you are needing both a 4-way and 7-way connector and do not want to wait on the Tekonsha item # 22117, you will need the Universal Installation Kit for Trailer Brake Controller item # ETBC7. The kit includes a pre-wired 7- and 4-way trailer connector that mounts easily at the rear of your Tacoma with an included bracket. This kit is designed for use on a vehicle with an existing 4-way flat trailer connector and plugs directly into it.

For a brake controller I recommend the I recommend the Tekonsha Prodigy P3 Trailer Brake Controller item # 90195. This is a proportional brake controller that activates your trailer brakes in proportion to your Tacoma's braking action. If you use the Tekonsha item # 22117 the Prodigy P3 will plug directly into the included brake controller port.

expert reply by: Jerred H

0

Answer 1

If you are just looking to tow a trailer with lights and without brakes, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part #C56349. This will give you a 4-Pole flat on the back of the Tacoma to tow a…

view full answer...

Answer 2

I have a solution for you, but it will require a little wiring and it is not the Trailer Wiring Harness part #20137. There currently isn't a plug and play replacement 7-way available for your 2006 Toyota Tacoma so the best recommendation I can…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Recommended 7-Way Connector for a 2022 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching