What is Max Tongue Weight of Bulldog Collar-Lok Coupler # BD028463

Question

Question:

What is the max. tongue weight for this coupler?

asked by: John R

0

Expert Reply:

The max tongue weight for the Bulldog Collar-Lok Coupler # BD028463 that you referenced is 1,250 lbs.

expert reply by: Jameson C

0

Answer 1

A trailer's 17-digit VIN will usually be located near the tongue area on an inside-facing surface where the information will be protected from impacts from road debris. Although this placement is common there is no absolute rule about where a…

view full answer...

Answer 2

The auxiliary 12-volt wire that runs from the 7-way connection to 7-way trailer plug will supply 12-volt power from the vehicle to the trailer. The 12 -volt power will allow interior or exterior lights to run that are not wired in to the…

view full answer...

Answer 3

90-120 ft lbs of torque is probably about right for your 15 inch trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher. You'll need to know the diameter of the…

view full answer...

Answer 4

What you would need is a switch like the #D16740, an isolation solenoid part #PK5231201 and some wire like #12-1-1 (sold by the foot). You'd run wire from the positive post of the battery to the terminal on the side of the solenoid and then on…

view full answer...

Answer 5

The Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 10" Travel - 1,000 lbs #MJ-1206B can absolutely be installed on the tongue part of the trailer. The video you are referring to I have attached and it wasn't added to the…

view full answer...

Answer 6

The only pin that should be continuously showing 12V power on the 7-Way connector on your vehicle is the 12V power circuit which is normally the black wire but not always. In 7-way wiring the 12V auxiliary power feed is carried on the contact at the…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

What is Max Tongue Weight of Bulldog Collar-Lok Coupler # BD028463

Product Page this Question was Asked From

Continue Researching