Locking Pin Set To Secure B&W Tow & Stow 3-Ball Mount # BWTS10048B

Question

Question:

Hi B and W hitch , TS20048B 2.5 in hitch 14 k rating . I don’t see how it is theft deterrent ? Does it require multiple locking pins to secure all the parts? Does that void tow rating? Thsnks

asked by: Michael S

0

Expert Reply:

To secure the B&W Tow & Stow 3-Ball Mount # BWTS10048B you will need the InfiniteRule Locking Pins # 34061775-D. These pins are all lockable with a 42,000lb sheer strength. It will allow you to remove all the included pins which come with the Tow & Stow for locking pins including a locking hitch pin. These pins will not void the tow rating for the hitch.

expert reply by: Bud M

0

Answer 1

The InfiniteRule Locking Pins for B &amp; W #34061775-D would be the lock set you would want if you have the B&amp;W Tow and Stow because it will provide you with a lock for each pin location on the hitch. If this is not the…

view full answer...

Answer 2

We have just what you need to lock all of the pins of the B and W Tow n Stow Ball Mount part #BWTS10037B that you referenced with the part #34061775-D. This comes with lock pin replacements for all of the platform pins as well as the hitch pin and…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that&#39;s going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

The OEM prep package consists of 4 &quot;pucks&quot; in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 10

Yes there is! The Husky 31326 hitch is made to fit the industry standard fifth wheel rails (ISR). The Curt Adapter #C88KR is also made to the same industry standard measurements. So the Curt Adapter #C88KR will be exactly what you need to use your…

view full answer...

Answer 11

If the trailer is less than 1 inch off of being perfectly level either up or down then it will be perfectly fine. Having it slightly higher would be better because presumably the tongue weight of the trailer will pull it down a little. You could…

view full answer...

Answer 12

It's a bummer but you can't use a pivoting pin box with a fifth wheel hitch that only attaches to a gooseneck ball as the additional twisting torque that these types of pin boxes but on hitches requires four attachment points instead…

view full answer...