Replacement Shoes for Dexter 6K Electric Trailer Brake Kit with Parking Brakes

Question

Question:

Dear ETrailer, Do you sell the brake shoes for this part:23-112-113 Thank you,

asked by: Livia G

0

Expert Reply:

I was able to confirm with Dexter that the correct replacement shoes and lining kit for the Dexter Electric Trailer Brake Kit with Parking Brakes part # 23-112-113 is the Replacement Shoe and Lining Kit part # DX28FR. The shoes are the same for the 6K and 7K axles.

expert reply by: Conner L

0

Answer 1

For your 6,000 lbs Dexter axles, the Dexter Electric Trailer Brake Kit w/ Parking Brakes - 12" - Left and Right Hand Assemblies - 6K, #23-112-113, will be the set of brakes for your trailer's rear axle. This kit will include both…

view full answer...

Answer 2

We have the Dexter Electric Trailer Brake Kit w/ Parking Brakes - 12" - Left and Right Hand Assemblies - 6K Item #23-112-113 which is going to fit the same drum and bolt pattern as a 7k axle and would work great. In general the 5.2k to 7k…

view full answer...

Answer 3

In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your…

view full answer...

Answer 4

The MTI number on your 8-201 hubs is simply a casting number. It does not indicate any information about the hubs or have anything to do with the actual part number. I'm not surprised to hear you have different outer bearings between the…

view full answer...

Answer 5

The difference between Blue Ox SwayPro heads #BXW4011 and #BXW4012 is the angle at which the trunnions are relative to the head. Head #BXW4012 is designed for underslung, also called bottom-mount, couplers so the bars are not at as a steep of an…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...