Bearing Kit For Hub on 4,400 lb Axle

Question

Question:

Hello, looking for a bearing kit for a double 4400 lb axles RV

asked by: David T

0

Expert Reply:

While there isn't a kit, we do have the correct bearings and races for a hub like # 8-407-5UC3-EZ that fits a 4,400 lb axle. So what you will need are the following:

- Replacement Trailer Hub Bearing # L44649

- Replacement Race # L44610

- Replacement Trailer Hub Bearing # LM67048

- Replacement Race # LM67010

- Grease Seal # 58846

Then if you need one use Bearing Packer # ALL647646 along with LubriMatic LMX Industrial Strength Grease # L11390.

expert reply by: Kyle S

0

Answer 1

You are correct, 4,400 lb axles have basically gone away. There are no axles or spindles that use your #8-407-5UC3-EZ hub and drum bearing combination either to try to fabricate a new axle. This means your only option will be to swap out the axles,…

view full answer...

Answer 2

I do have an option for you but the only trailer hub we offer with these bearings/measurements, L68149 (1.378" inner diameter) and LM67048 (1.25" inner diameter) is the Trailer Hub and Drum Assembly part #8-407-5UC3-EZ which has a 6 on…

view full answer...

Answer 3

The hubs used by the Dexter 4400 lb axle are 3500 lb hubs that have had their weight capacity upgraded by using a LM67048 outer wheel bearing. A 4400 hub like the #8-407-5UC3-EZ would use the same #58846 grease seal as a 3500 lb hub would. Long story…

view full answer...

Answer 4

From the axle tag you provided (thank you!), you do indeed have a 4,400 pound Dexter axle. The only hub/drum we carry that is compatible is the Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ.…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...