What Grade is the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs

Question

Question:

Can we find out what grade this bolt is and list it in the specs?

asked by: Robert

0

Expert Reply:

The Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs part # 126B2 has a grade 5 rating. There are three radial lines on the head of the bolt which indicates the rating.

expert reply by: Conner L

0

Answer 1

The Nylon Bushings - 9/16" Inner Diameter, 3/4" Outer Diameter - 1-3/4" Long - Qty 6 #SP05-060 you were looking at are the only option for bushings in this size. While the 9/16" inner diameter is common, the 3/4" outer…

view full answer...

Answer 2

I reached out to the manufacturer and the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3-5/16" Long #126B2 is a pressed in zerk fitting, so it cannot be replaced. There are not threaded zerk fittings available for…

view full answer...

Answer 3

The term, wet, in this case means that the head of the bolt has a grease Zerk in it and there is a channel that leads to center of the bolt. This makes it easy to grease the bolt while installed, as you can put a grease gun right up to the Zerk and…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

What Grade is the Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs

Product Page this Question was Asked From

Continue Researching