Can Lippert Polarity Reversing Solenoid LC118246 Be Installed With a Strap

Question

Question:

My present solenoid is trapped to the top of the pump motor with a type of hose clamp. The Part # appears to be 118246. Is the replacement part compatible with the use of this strap.

asked by: Paul

0

Expert Reply:

If the Lippert Polarity Reversing Solenoid # LC118246 looks to be the same design as the 118246 that you're currently using then you should be able to use the strap in the same manner. The only time something would change is if this part looks different than what you have.

expert reply by: Jon G

0

Answer 1

Yes; this could potentially be an issue with the solenoid and there is a way to test whether or not this is the cause of the issues. What you'll need to do is switch the wiring between the two cylinders to see if the same thing happens, but in…

view full answer...

Answer 2

If the valve on your solenoid was open then that would explain why nothing was operating properly. The valve being open would mean that the pressure would have been released. Since you closed the valve, as it is supposed to be, that is why everything…

view full answer...

Answer 3

The location for the solenoid controller like the Lippert Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units #LC118246 will vary and in order to find what you're looking for you're going to need to trace the wiring going to…

view full answer...

Answer 4

You can test the function of the slider's troublesome hydraulic actuator cylinder by swapping the wiring between the two cylinders. If the bad one now works (when connected to the wiring for the other) then you know the issue is not the cylinder,…

view full answer...

Answer 5

It does look like you are missing a wire connection on your solenoid. I attached a picture that shows a wire lead ran to the same terminal you just have rans with that copper bar. I believe that's the missing connection you need to make.

view full answer...

Answer 6

It sounds like the ground isn't the issue because you bypass that with the cables and still have the clicking of the solenoid #LC118246. It sounds like the solenoid has gone bad and needs replacing. You have confirmed the motor works, so I'd…

view full answer...

Answer 7

The 214-1231-A61-06 solenoid actually replaced your older 214-1231-A11-06, so the correct replacement for your 06 Keystone Montana Mountaineer is the Lippert Polarity Reversing Solenoid by Trombetta for Hydraulic Power Units #LC118246.

view full answer...

Answer 8

The Lippert Replacement Reverse Polarity Solenoid for RV Hydraulic Slide-Outs part #LC136046 and part #LC118246 are the same solenoid but vary in how they mount. The part #LC136046 mounts using a strap around the motor like what you have therefore…

view full answer...

Answer 9

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 10

I have a complete replacement camera system option for you, but since your current camera system is no longer made there are no replacement cameras available that use your same monitor. I recommend replacing it with the Voyager WiSight 2.0 Wireless…

view full answer...

Answer 11

That's weird, the 7-Way Vehicle Power Adapter for Furrion RV Observation Camera #FR87PR should allow you to use your camper at the same time as that's what it's designed for. If you want to just avoid the adapter all together, I would…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Can Lippert Polarity Reversing Solenoid LC118246 Be Installed With a Strap

Product Page this Question was Asked From

Continue Researching