Replacement Bearings, Races and Oil Seal Used In Dexter Bearing Kit K71-722-00

Question

Question:

LOOKING FOR A BEARING KIT TO MATCH WITH THIS : K71-722-00 Bearing Kit 9-10K Gd Dx 25580/387A DO YALL CARRY THIS SET? THANKS!

asked by: Barbara

1

Helpful Expert Reply:

While we do not have a kit that includes everything from the Dexter K71-722-00 bearing kit we do have all the parts that are included with the kit.

Inner Bearing # 387A
Inner Race # 382A
Outer Bearing # 25580
Outer Race # 25520
Oil Seal # 10-51

expert reply by: Bud M

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 4

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 5

Hello Jeffrey, While I'm sure we have a bearing kit for your car trailer, we don't have any way of knowing off-hand or cross-referencing what bearings you need. You mentioned you have them out, so you should be able to see the part number…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 8

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 9

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 10

The only difference between the #RG06-050 and Timken #TMK58ZR is the brand and quantity. Timken is typically considered to be a high quality brand, particularly for their USA made bearings. The #RG06-050 comes with two seals so it is the better…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Replacement Bearings, Races and Oil Seal Used In Dexter Bearing Kit K71-722-00

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching