Trailer Hitch For A 2016 Subaru Outback Wagon With A 1.5 Inch Hitch Pin Hole Depth

Question

Question:

Weve got a 2016 Subaru Outback and a Thule Easyfold XT bike rack. Does your model # 76227 have a 1.5 hitch pin hole depth? The OEM Trailer Hitch from Subaru had a 1 pin hole depth, so it wasnt compatible.

asked by: Michael P

0

Expert Reply:

I have the perfect trailer hitch that has a 1.5 inch hitch pin hole depth and that is confirmed to fit your 2016 Subaru Outback Wagon!

The Draw-Tite Max-Frame Trailer Hitch Receiver # 76227 has a 2-1/2 inch hitch pin hole depth from the center of the hitch pin hole to the closet part of the rack. So your Thule Easyfold XT will work perfect with this hitch.

The hitch has an easy, bolt-on installation with no welding required. It has a black powder coated finish that covers an e-coated base that offers a superior rust protection. The hitch has a maximum tongue weight up to 600 pounds. I would recommend checking your vehicle's manual to find out the proper tongue weight capacity for your 2016 Subaru Outback Wagon.

I attached an installation video link below.

expert reply by: Noah E

0

Hitch Pin Measurements
(click to enlarge)

Answer 1

For replacement hardware for your Yakima Kingpin 4 you need the Replacement Shank and Pivot Hardware #Y8780018. This comes with the hitch bolt and clip, along with the hex bolts, washers, bolt sleeves and lock nuts required to mount the pivot shank.

view full answer...

Answer 2

When the Draw-Tite Class III Max Frame Receiver Hitch #76227 is installed on your 2018 Subaru Outback Wagon, the hitch receiver will actually sit about flush with the rear bumper. There will be a distance of just around 2-1/2 inches from the hitch…

view full answer...

Answer 3

I went out to the warehouse to take the measurements you asked for and found that the hitch measured approximately 2-1/2 inches from the center of the hitch pin hole to the end of the receiver. In terms of the receiver depth of the Draw-Tite #76227…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Trailer Hitch For A 2016 Subaru Outback Wagon With A 1.5 Inch Hitch Pin Hole Depth

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching