Replacement Hardware for Yakima Kingpin 4

Question

Question:

Hi, Im looking for the bolt kit I have a Kingpin 4 and it was unclear which bolt I needed from the website.

asked by: John A

0

Expert Reply:

For replacement hardware for your Yakima Kingpin 4 you need the Replacement Shank and Pivot Hardware # Y8780018. This comes with the hitch bolt and clip, along with the hex bolts, washers, bolt sleeves and lock nuts required to mount the pivot shank.

expert reply by: Robin H

0

Answer 1

I measured the bolt that is included in the Yakima Replacement parts kit #Y8780022 and found it has the following dimensions: Overall Length 4-5/8 Hex Head Size 13/16 Thread diameter 1/2 Length of Thread 2-1/2 I prepared a photo with these dimensions…

view full answer...

Answer 2

The Yakima Replacement Hitch Bolt and Clip for Yakima HoldUp Hitch Mounted Bike Carrier, part #Y8890200, is a 5/8 inch bolt. The size wrench you would use to install or remove this bolt is 15/16 inch.

view full answer...

Answer 3

You would want to get a Hitch Reducer 2 inch to 1-1/4 inch Trailer Hitch Receiver, part #HT02, to reduce your 2 inch hitch opening enough for you to install your Yakima BigHorn 4 Bike Hitch Bike Rack, part #Y02405. I attached a review video for this…

view full answer...

Answer 4

The Yakima Replacement 2 Inch Hitch Adapter, #Y8890174, is designed for use on the Yakima Flipside, StickUp, and the DoubleDown models. Since I do not know what model Yakima bike rack you have it will be hard to determine if this adapter will work on…

view full answer...

Answer 5

Sounds like you are looking for an adapter like the part #HT02 which will convert your 2 inch hitch to a 1-1/4 inch hitch so that you can use your current bike rack in a 2 inch hitch.

view full answer...

Answer 6

We can get a 1-1/4 hitch accessory in a 2 inch hitch without modifying the accessory. Use this hitch reducer #HT02 to convert your 2" hitch to a 1-1/4" hitch. You cant use the RockyMounts adapter sleeve #RKY54FR is because the shank does…

view full answer...

Answer 7

Thanks for the picture of hitch pin, but what was really helpful was actually the set of instructions you have in the background. Based on that you have the first version of the BigHorn which was made around 2001 and the correct hitch pin replacement…

view full answer...

Answer 8

I spoke with my contact at Yakima regarding your older model 4-bike rack. He said that based on your description, the correct replacement hitch bolt is the part #Y8890200. He stated that this bolt was actually re-designed with the wider Toyota hitch…

view full answer...

Answer 9

For a replacement hitch pin for your Yakima BuckHorn bike rack you would want the part #Y8780018.

view full answer...

Answer 10

For the Replacement Rubber Straps for Yakima Bike Racks with SwitchBlade Cradles QTY 2, #8890221, the holes are 1/2 inch in diameter and it is 9 inches long. These straps can be found on Yakima SwingDaddy, FlipSide, DoubleDown, BigHorn, QuickBack,…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Hardware for Yakima Kingpin 4

Product Page this Question was Asked From

Continue Researching