Will The Equal-i-zer L-Pins and Clips # EQ95-01-9430 Fit a Fastway E2 Weight Distribution Hitch?

Question

Question:

Will the product: Replacement L-Pins and Clips for Equal-i-zer Weight Distribution Systems - 6K to 14k - Qty 2 Item # EQ95-01-9430 Work on a E2 fastway roundbar weight distribution system? I like the snap mechanism, but because the round bar is flat on the end towards the trailer, it does not seem like the top of the L pin will be sitting on the bar, does that matter?

asked by: Heather B

0

Expert Reply:

Yes, the Replacement L-Pins and Clips for Equal-i-zer Weight Distribution Systems # EQ95-01-9430 can also be used to replace the L-Pin # FA92-03-9205 used on the Fastway E2 6,000-12,000lb weight distribution systems. The L-Pin simply holds the bar inside the sway bracket and prevents it from sliding out. It is compatible with both the round bar style you have and square bars.

expert reply by: Bud M

0

Answer 1

The L-pins on the Fastway e2 systems are a little different than those used with the Equal-I-zer system but #EQ95-01-9430 can be used. For the e2 system we also have replacement L-Pin #FA92-03-9205. The clip is #FA92-04-9208. Each of these are sold…

view full answer...

Answer 2

I reached out to my contact at Progress Mfg. about your question. They do not have a longer lever bar and they do not recommend using what I would call a "cheater bar" to extend that bar for greater leverage. They suggested that when you…

view full answer...

Answer 3

While I would not recommend using a different clip, and the L-Pins do not come with a different hole size, I do have a solution. Since you have the Fastway e2 Weight Distribution #FA92-00-0600 you can use the Replacement L-Pins and Clips for…

view full answer...

Answer 4

The Replacement Trivet Support Bumper for Furrion Chef Collection Gas Cooktop #CFGH4ZSASSTRIVETSPRT is a quantity of 1 single replacement bumper for the Furrion RV Cooktop #FGH4ZSASS.

view full answer...

Answer 5

The replacement parts that we have available for the Furrion RV Cooktop #FGH4ZSASS are listed below: - Replacement Gas Inlet Connector and LP Regulator Inlet Assembly for Furrion RV Cooktop #FR97PR - Replacement Ignitor for Furrion RV Propane Cooktop…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Will The Equal-i-zer L-Pins and Clips # EQ95-01-9430 Fit a Fastway E2 Weight Distribution Hitch?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching