Replacement L-Pins for Fastway e2 Weight Distribution Systems

Question

Question:

Do the new Equalizer L pins work on the e2 hitch? Also does the Sway Bracket Jackets 95-01-5150 from Progress Mfg, Inc fit on the e2 hitch? Thanks for your help.

asked by: John B

0

Expert Reply:

The L-pins on the Fastway e2 systems are a little different than those used with the Equal-I-zer system but # EQ95-01-9430 can be used. For the e2 system we also have replacement L-Pin # FA92-03-9205. The clip is # FA92-04-9208. Each of these are sold in quantities of one.

The Equal-I-zer bracket jackets you referred to, part # EQ95-01-5150 will work with your Fastway weight distribution system. However, if you use the bracket jackets, you'll significantly reduce the effectiveness of the sway control feature that the E2 provides. The jackets will prevent the metal on metal friction between the spring bar and the L bracket attached to the trailer frame.

expert reply by: Michael H

0

Answer 1

I reached out to my contact at Progress Mfg. about your question. They do not have a longer lever bar and they do not recommend using what I would call a "cheater bar" to extend that bar for greater leverage. They suggested that when you…

view full answer...

Answer 2

Yes, the Replacement L-Pins and Clips for Equal-i-zer Weight Distribution Systems #EQ95-01-9430 can also be used to replace the L-Pin #FA92-03-9205 used on the Fastway E2 6,000-12,000lb weight distribution systems. The L-Pin simply holds the bar…

view full answer...

Answer 3

While I would not recommend using a different clip, and the L-Pins do not come with a different hole size, I do have a solution. Since you have the Fastway e2 Weight Distribution #FA92-00-0600 you can use the Replacement L-Pins and Clips for…

view full answer...

Answer 4

Sway Bracket Jackets for Equal-i-zer Weight Distribution Systems #EQ95-01-5150 are fully compatible with the Replacement L-Pins and Clips #EQ95-01-9430. Both are suited to weight distribution systems rated between 6K and 14K.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Replacement L-Pins for Fastway e2 Weight Distribution Systems

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching