Replacement Lifting Mechanism for MaxxAir 7000K Roof Vent Fan

Question

Question:

Hello, I have a MaxxAir 0007000K Deluxe installed in my van. Recently the small part that lifts the dome broke off. I am trying to figure out which part replaces it? The spring arm is still intact that piece that engages it is what broke. Can you help me find the right part? Or is it possible to replace the whole dome with a less complicated mechanism? Thank you

asked by: Val Y

0

Expert Reply:

It sounds like you could be referring to either Replacement Operator Mechanism part # MA10-20281K-1AF or Replacement Lift Arm part # MA10-20222KS which are both fits for a MaxxAir 7000K Roof Vent Fan. If you need a different part let me know but these are all that's available for the lifting mechanisms aside from the Replacement Lift Motor part # MA10-20270.

If you're looking for a less complicated replacement that would be the MaxxAir MaxxFan Mini Roof Vent part # MA00-04401M which is just a powered vent fan with manual lift lid.

expert reply by: Conner L

0

Answer 1

I checked the repair parts list for a MaxxAir 7500K Roof Vent and the Replacement Operator Mechanism for MaxxAir MaxxFan Plus or MaxxFan Deluxe Roof Vents part #MA10-20281K-1AF is listed as a fit without any exclusions such as date of manufacture so…

view full answer...

Answer 2

Sounds like you have a damaged or worn out roof vent operator and need to replace it with the part #MA10-20281K-1AF since you said the motor doesn't want to fully open or close the lid and it's difficult to turn by hand.

view full answer...

Answer 3

When installing the #MA10-20281K-1AF replacement operator, you might need to 'clock' the mechanism slightly which could take a little bit of trial and error, but the replacement operator does include installation instructions. I've…

view full answer...

Answer 4

The model number for your MaxxAir vent like the MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan #MA00-04401M, can be found on a sticker stamped on the upper side, if you can't find it there you can also find it located on the bottom and visible when…

view full answer...

Answer 5

I checked with the manufacturer and the tiny screw you're seeing is a set screw. You will use an Allen wrench/key to remove this. I'm attaching a picture with a set of installation instructions for you to refer to when you're replacing…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...