What Is The Torque Specs On U-bolts #590050-00

Question

Question:

what to torque them to???? the ford 1s say 300 psi. are these the same.

asked by: Jon

0

Expert Reply:

Per the manufacturer The Extended U-Bolt Kit for Roadmaster Anti-Sway Bar # RM-590050-00 are tightened down evenly snug and then turn a 1/4 inch more.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

The Roadmaster Rear Anti-Sway Bar for Motorhomes #RM-1139-143 can use your factory u-bolts if they are long enough. If they are not, then Roadmaster recommends using the 7/8 inch diameter u-bolts that are longer (most likely the larger diameter due…

view full answer...

Answer 2

The Blue Ox Acclaim Tow Bar #BX4330 that you referenced can be used with base plate kits that are between 23 and 30 inches apart.

view full answer...

Answer 3

There are adapters that allow for a Roadmaster tow bar to be adapted to Blue Ox base plates, but unfortunately they are not compatible with the Stowmaster tow bar. I attached a chart that details all of the adapters and their applications. For a…

view full answer...

Answer 4

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 5

The Atwood #AT3308046006 cover that you selected will likely work just fine. I contacted the manufacturer and they did not have your model 600315.321 so I can't spec out the exact one. There may be another sticker on your unit ending in .331 or…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 11

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Is The Torque Specs On U-bolts #590050-00

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching