Diameter of Hitch Pin # 889-0231 For Yakima DoubleDown Ace, HighLite, LiteRider, or RidgeBack Rack

Question

Question:

Trying to get a replacement pull pin for my rack I think it is a ridgeback. Can you tell me the diameter of the pin for the Yakima pn 889-0231.

asked by: Ray

0

Expert Reply:

The Replacement Hitch Pin # 889-0231 is 3/8" in diameter.

expert reply by: Bud M

0

Answer 1

The pin of the Replacement Tongue Safety Pin for Yakima Dr. Tray and HoldUp EVO Bike Racks #Y57FR has a diameter of 3/8".

view full answer...

Answer 2

The best spot to install the Trailer Connector is on the bed sidewall on the drivers side, between the wheel well and the tail gate. We have an installation video showing this Curt 5th Wheel and Gooseneck Wiring Harness #C56000 being installed on a…

view full answer...

Answer 3

There is a replacement hitch pin available for the Yakima DoubleDown Ace bike rack, but Yakima does not offer one that locks because the locking feature is on the hand knob. So in order to replace the hitch pin, I verified with Yakima that the…

view full answer...

Answer 4

Since the lock number of your hitch lock is only listed on the side of the lock core, and yours is locked and therefore not accessible, the only solution is to replace what you have with a new hitch bolt and lock. For that you'd need part…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Diameter of Hitch Pin # 889-0231 For Yakima DoubleDown Ace, HighLite, LiteRider, or RidgeBack Rack

Product Page this Question was Asked From

Continue Researching