What Wire Gauge Is The Optronics LED Trailer License Plate Light?

Question

Question:

Can you please tell me what gauge of wire is used on the LPL56CB? The trailer I’m going to install this on current has 14 gauge wire and I want to be sure it can make it work before I purchase the light. Thanks

asked by: Ray

0

Expert Reply:

The Optronics LED Trailer License Plate Light with Bracket # LPL56CB uses 20 gauge wire. This thin wire is all that is needed to power the led light as it only draws 0.045 amps at 12.8 volts.

expert reply by: Bud M

0

Answer 1

Unless ShoreLand'r has a special wiring harness kit that has all of the connectors for your lights (which is very unlikely) you are looking at a complete custom job. You can either choose to replace the damaged wiring that you see with 16 Gauge…

view full answer...

Answer 2

The Optronics Submersible LED Trailer Light Kit #TLL9RK referenced in your question uses 20 gauge wire for the included 25 foot wiring harness. This is a really nice light kit that also includes two stud mount, waterproof LED tail lights and the…

view full answer...

Answer 3

The Hopkins Wiring #HM11141995 and Curt Wiring #C56331 for your 2011 Dodge Grand Caravan install the same way but the Curt wiring is much more reliable, which is something you can see right away since the Curt has a 1-year warranty and the Hopkins is…

view full answer...

Answer 4

Yes, you can power and ground the LED license plate light #LPL91CB using the 7-Way trailer connector. The power wire would run to the running light circuit and ground to the ground circuit. If you wanted to wire those up to a trailer-side 7-Way you…

view full answer...

Answer 5

You will not need to add any diodes or other modules to prevent hyperflashing or any other bizarre taillight behavior when you install this Optronics Tail Light #STL78RB on your trailer. If you were installing LED tail lights on a vehicle and…

view full answer...

Answer 6

The 5-way flat trailer connector is most commonly found on boat trailers that have hydraulic brakes. The fifth wire is hooked up to the reverse light circuit on the vehicle which then sends a signal to the hydraulic coupler to disengage the trailer…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

The proper replacement inner assembly member for your UFP 34043 would be indeed be the the Dexter #DX99FR which is compatible with disc brakes. The replacement has an electric lock out and has a 7500K capacity and is intended to work with a 2 inch…

view full answer...

What Wire Gauge Is The Optronics LED Trailer License Plate Light?

Product Page this Question was Asked From

Continue Researching