Will Dexter Heavy-Duty Suspension Kit # K71-359-00 Work with 5,200 lb Tandem Axle Kit

Question

Question:

Looking at your heavy duty leaf doing Susp kit what won’t do I need for a 5200 pound lippert axles.

asked by: Jim S

0

Expert Reply:

The Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers # K71-359-00 is going to work great on your 5,200 lb Lippert axle setup. The dimensions of this kit are the same that would be used on a 5,200 lb tandem setup like you have so it would fit fine.

expert reply by: Jameson C

0

Answer 1

Excellent question, and the difference between the two kits comes down to the dimensions of the equalizers. What you will want to do is match up the size of your equalizer with the size of the equalizer in these kits. - 6" Long, 4" Tall…

view full answer...

Answer 2

To determine if the Dexter Heavy-Duty Suspension Kit #K71-359-00 will work with the current suspension on your 2003 Carson trailer you will simply need to measure your equalizers and shackle straps that you have on them right now. The equalizers that…

view full answer...

Answer 3

You have the correct parts selected for your Dexter EZ Lube axles. The Bearing Kit for #84 Spindle, L44649/L68149 Bearings, 10-19 Double Lip Seal, item #BK2-100, contains the Inner bearing and race, outer bearing and race, grease seal and cotter pin.…

view full answer...

Answer 4

I do have an option for you but I cannot give you exact bearing numbers for your trailer unless provided with spindle measurements or the trailer's VIN (if the manufacturer is still in business). I can however tell you that the two most common…

view full answer...

Answer 5

I was able to do some digging and found out that Sure-Trac trailers use either a Dexter or Lippert axle, and both of these 3,500 lb axles use the same bearings and grease seal, so we have exactly what you need. The Bearing Kit for #84 Spindle…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 12

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...