Replacement Curt Trailer Hitch Hardware For 2008 Dodge Ram Pickup

Question

Question:

How’s it going I have a Curt 15704 hitch i seemed to misplace the mounting hardware for it is there anyway to get another bolt kit for it thanks

asked by: Dan

0

Expert Reply:

We have the replacement hardware you need!

The Replacement Hardware Kit # RHK is the kit you will need. There is two boxes you will have to fit out the first box asks for the hitch item number type in C15704. The second box has a drop down arrow select Curt.

This kit will replace all lost hardware needed to install The Curt Hitch # C15704 on your 2008 Dodge Ram Pickup.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

Yes, the Curt hitch part #C15704 does fit a 2008 Ram 1500 as long as the truck does not have a factory hitch.

view full answer...

Answer 2

In regards to the Curt Trailer Hitch Receiver part #C15704 which is a fit for a 2003 Dodge Ram 3500, the distance from the top of the flange to the top of the hitch cross tube is 6.65" exactly.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Replacement Curt Trailer Hitch Hardware For 2008 Dodge Ram Pickup

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching