Replacement Parts For Thomas Payne Power Recliner That Will Not Recline

Question

Question:

How do I get repairs or parts for Thomas Payne power recliners that dont recline.

asked by: Judy T

0

Expert Reply:

When looking into why your Thomas Payne Power Recliner won't recline it sounds like the control boxes have gone bad.

The Replacement Control Box For Thomas Payne Momentum Recliners and Sofas # 195-387596 will get your recliner to recline again. This is for the Momentum Recliner. If you have The Thomas Payne Seismic Recliner you will need The Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas # LC36FR.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

We have the control box you are looking for with the part #LC36FR.

view full answer...

Answer 2

Thanks for the picture of your current module. Based on that the correct replacement module is the part #LC36FR that you referenced.

view full answer...

Answer 3

Yes, the Replacement Power Control Box for Thomas Payne Seismic Recliners and Sofas #LC36FR does come with all the wires shown in the photos, including the connector. Keep in mind this is a replacement specifically for the Seismic line of Thomas…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Replacement Parts For Thomas Payne Power Recliner That Will Not Recline

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching