Replacement Switch Solution For A Superwinch T1500 Winch

Question

Question:

I have a superwinch t1500 that works great. This past weekend the Switch broke. Do you have anything I can replace it with? Thanks

asked by: David M

0

Expert Reply:

Sure thing!

You can use the:

-Replacement Momentary Rocker Switch for Bulldog Winch 4-Switch Panel w/ Lighted Breakers # BDW20374 with your Superwinch T1500 Winch.

This switch measures 15/16" wide, 1-15/16" tall, 1-15/16" deep, and is water and weather resistant to IP68 specifications.

expert reply by: Bryce D

0

Answer 1

I'm not quite sure what you mean by the "heart", however for your Ventline VD0434 we have the replacement screen frame #BVA0444-32, the replacement screen #BVD0434-31, the replacement lid #BVD0449-A01, and the replacement…

view full answer...

Answer 2

We do not carry the replacement axle for your P12 7K Axle. We do however have the brake assemblies and bearing kit or hub/drum assemblies to assist based on what I can find online for a 7K Dexter axle. You will most likely want the Bearing Kit,…

view full answer...

Answer 3

It took a little while to get your information from Dexter. Your axle is a #13 Torflex Axle which is rated for a capacity of 8,000 lbs. We don't have an 8,000 lb capacity replacement, but we do have 7,000 lb capacity Axle-less Systems you may…

view full answer...

Answer 4

I reached out to my contact at Dexter Axle who said that your axle is rated for 3,500 lbs and it uses inner bearing #L68149, outer bearing #L44649, and the grease seal #58846. All of these can be found in the kit #BK2-100 if you are needing to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Switch Solution For A Superwinch T1500 Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching