MaxxAir Vent Cover For 2013 Motorhome

Question

Question:

I have a 2013 Newmar Baystar 3902. Can you tell me what Maxxair fan vent cover is best fit for my Motorhome.

asked by: Joe T

0

Expert Reply:

Assuming you have a standard 14" x 14" vent on the top of your motorhome (we have no way of knowing what specific vent you have), you can use the MaxxAir FanMate vent cover, but you'll have to drill holes into the side of your vent with the included hardware instead of using the clips. So you can use any of the following, depending on the color you want:

- Smoke: MaxxAir FanMate RV and Trailer Roof Vent Cover # MA00-955003

- Black: MaxxAir FanMate RV and Trailer Roof Vent Cover # MA00-955002

- White: MaxxAir FanMate RV and Trailer Roof Vent Cover # MA00-955001

expert reply by: Kyle S

0

Answer 1

The MaxxAir FanMate RV and Trailer Roof Vent Cover #MA00-955002 will fit your MaxxAir 00-04900K, but it will not allow the lid to fully open. This is a clearance issue that is the same for every other RV roof vent on the market. Manufacturers will…

view full answer...

Answer 2

No the MAXX AIR II Vent Cover #MA86JR that you referenced does not come with a bug screen built into it. Just the screen is not available as it does not separate.

view full answer...

Answer 3

Based on the dimensions you listed we have the part #010-180-00 which would fit and work well. This has an outer diameter of 2.33 inch and an inner diameter of 1.68 inch like you need so it would work well.

view full answer...

Answer 4

Good morning, Don. The 3/4" wide butyl tape is exactly what we recommend for installing a roof vent such as the MaxxFan #MA00-07000K. We actually sell a roof vent install kit part #344270KITW that comes with sealant, screws and a 30' roll of…

view full answer...

Answer 5

For your Karavan trailer I recommend LED tail lights #STL57RB and #STL56RB. They are a little shorter at 6-1/16 inches but they do mount on studs spaced 2 inches apart on center. they are 3-5/8 inches tall and 2-1/4 inches deep overall. I have linked…

view full answer...

Answer 6

To add a in-bed 7-way to your 2024 Chevy Silverado 2500 to make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7' Long item #C58FV. This harness puts a 4-way and 7-way…

view full answer...

Answer 7

All you need for attaching a brake controller to your 2022 Hyundai Palisade is the receiving-end setup. For that setup, you need to have a 4-way and a 7-way wiring harness in order to use a brake controller. If you do not have the 4-way installed…

view full answer...

Answer 8

Based on my research a hub with a part number 46845 is a hub with a 5 on 4-1/2" bolt pattern and uses inner bearing #L68149 and outer bearing #L44649 like what the bearing kit part #BK2-100 that you referenced provides. The axle should have…

view full answer...

Answer 9

If the vent fan you have now is reversible then there should be a button on the assembly next to the other controls. However, if the fan is not reversible then all you need to do is reverse the wires on the motor (not the circuit board) and that will…

view full answer...

Answer 10

Great question! The Timbren Axle-Less Trailer Suspension System #ASR2KHDS04 has a standard size spindle which is why it is for regular tires. The Timbren Systems #ASR2KHDS03 and #ASR1THDS03 have longer spindles which can accommodate wider tires and…

view full answer...