Can 2022 Tundra OEM Brake Controller be Used with Hydrastar EOH Actuator

Question

Question:

Is this compatible with 2022 Tundras brake controller?

asked by: Stuart T

0

Expert Reply:

Your 2022 Toyota Tundra's brake controller does have electric over hydraulic mode so it would work just fine with the Hydrastar Electric Over Hydraulic Actuator Kit # HBA-10-252-82.

expert reply by: Jameson C

0

Answer 1

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 2

The Titan Zinc-Plated, Leverlock Coupler #T4845000 that you referenced is designed to fit on a trailer tongue that measures 3 inches wide. If you measure the width of the insert portion of your surge coupler and it's 3 inches wide this will…

view full answer...

Answer 3

Hydraulic brakes are better suited for boat trailers for the simple fact that wires and water do not like to cooperate with each other, but the etrailer.com Self Adjusting Electric Trailer Brakes, #AKEBRK-35L-SA, can be used on a boat trailer…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Can 2022 Tundra OEM Brake Controller be Used with Hydrastar EOH Actuator

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching