Is the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack Sealed and 30 amp Rated

Question

Question:

The boot around it means the switch is sealed I hope? And is it 30 amp it doesnt say this is from my Fox mountain 5th wheel it needs to be 30 amps

asked by: Daniel H

0

Expert Reply:

The Replacement Extend/Retract Switch for Lippert Electric Trailer Jack # LC49MD is the correct switch for the Lippert Electric Trailer Jack with Footplate # LC285318 which does use 30 amps. Yes, the boot around the switch does seal the switch when installed.

expert reply by: Scott S

0

Answer 1

There could be a few things that could be causing your electric trailer jack to malfunction. I will give a few starting points to begin to troubleshoot the problem. On some electric jacks there may be an inline fuse on the power wire going from the…

view full answer...

Answer 2

Since it won't retract you'll need to replace the switch with Replacement Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD.

view full answer...

Answer 3

For your electric jack, there are only three possible explanations for your jack not working with a charged battery. Either power is not getting to your motor, your motor is bad, or your ground connection isn't working properly. To test…

view full answer...

Answer 4

Yes, I have attached the wiring diagram of the Replacement Electric Jack Switch with Harness #LC387874 for you to reference. Basically the Blue wire goes to a 6A auto reset breaker, like part #LC134181, which then goes to the positive circuit for…

view full answer...

Answer 5

There was indeed a recall on the Lippert Smart Jack Electric Trailer Jack part #LC643589. It sounds like you have a pre-recall version but in order to confirm you can look on the back of the jack for a sticker on the stem with a serial number. If…

view full answer...

Answer 6

I checked with Lippert, the manufacturer, and the Replacement Tongue Jack for Lippert Ground Control TT Leveling System #LC421366 does not have replacement gears available. So if the gears are stripped and not working, that does mean you would need…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Is the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack Sealed and 30 amp Rated

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching