Replacement Ball Latch for Titan and Dico Model 60 Hydraulic Brake Actuator

Question

Question:

Dear Sir, I have been watching the video of the TITAN MODEL 60 LEVER LOCK DRUM BRAKE ACTUATOR and wonder if it is possible to purchase only the claw bracket mounted on the bottom - enclosing the ball. It is mounted with a bolt and nut. Mine is worn out and skewed after many years of use. Kindly reg.

asked by: Marcel S

0

Expert Reply:

If you're referring to the ball latch then yes, what you'll need is the Replacement Ball Latch for Titan and Dico Model 60 Hydraulic Brake Actuators part # T4335800.

expert reply by: Conner L

0

Answer 1

We do carry the exact replacement latch for the Titan Model 60 Brake Actuator you referenced. The latch by itself is the Replacement Ball Latch #T4335800 and there is also the Latch Repair Kit #T4045400 which will work.

view full answer...

Answer 2

Since it sounds like the latch is the source of the problem you will want to replace it with a repair kit. The correct repair kit for your Titan Model 60 Multi-Fit coupler is the Latch Repair Kit for Titan Multi-Fit Couplers and Brake Actuators…

view full answer...

Answer 3

Not all hydraulic trailer drum brakes can be reversed without the brakes activating. If the trailer has brake assemblies that have free-backing plates then a reverse lockout solenoid is not needed. If your neighbor can back his trailer up without the…

view full answer...

Answer 4

The Replacement Ball Latch for Titan and Dico Model 60 Hydraulic Brake Actuators #T4335800 that you referenced is the correct replacement latch kit you'd need for your actuator. In the picture I attached you can see that the top hole is supposed…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Ball Latch for Titan and Dico Model 60 Hydraulic Brake Actuator

Product Page this Question was Asked From

Continue Researching