Rhino Rack Roof Rack for a Van with a High Top Fiberglass Roof

Question

Question:

Roof rack I wanna put a rhino roof rack on my van I have a fiberglass high top and I don’t know if I could screw it to the fiberglass so I need real long legs

asked by: Gerald K

0

Expert Reply:

We do have roof rack options that will allow you to use a Rhino Rack roof rack on your van with a fiberglass roof. You can install the Yakima 42" Tracks for Roof Racks # Y01126 using the Capnuts, Washers and Bolts for Yakima Tracks # Y8810155 for fiberglass installation.

This would allow you to use the Rhino-Rack Roof Rack for Thule and Yakima Tracks # Y01-120B-NT.

expert reply by: Scott S

0

Answer 1

All you'll need to add tracks to your truck cap so you can mount a rooftop tent are the 42 inch Yakima tracks, which are the following part number: - Yakima 42" Tracks for Roof Racks #Y01126

view full answer...

Answer 2

The Yakima Control Towers like the part #Y8890027 (QTY 1) can fit the Yakima tracks like you mentioned with the Landing Pad 1 part #Y00221. This would work to use the Yakima Round Bars like #Y00409 which is a pair of 58 inch bars.

view full answer...

Answer 3

The screws that come with the Yakima Y8810155 are #10-32x1” and the capnuts are 1/2 x 1-1/4”.

view full answer...

Answer 4

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof…

view full answer...

Answer 10

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest…

view full answer...

Answer 11

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Rhino Rack Roof Rack for a Van with a High Top Fiberglass Roof

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching