Recommended Vent Cover For A MaxxAir MaxxFan 4751KS

Question

Question:

I have a Maxxair fan in my camper and want to purchase a cover for it. When the Maxxair 4751KS wall control is used to open fan lid or fan button is depressed the lid opens all the way, there is no halfway or partial open with wall control so Camcos wont work because they are too short when vent lib is fully open. I can manually open but that requires getting a ladder out and then the fan cant be operated. Any cover or fan upgrade options. My old camper I could partially open all vent lids but not this one. Thanks,

asked by: Steve C

0

Expert Reply:

For a MaxxAir 4751KS you'll want the MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip - White # MA76JR ( # MA26JR for Smoke and # MA86JR for Black). If your vent doesn't have the EZclip connectors then you'll simply need to screw the included brackets into the side of your vent to attach your new cover.

expert reply by: Kevin C

0

Answer 1

Since the Lippert stabilizer jack motor can clearly work since it can extend but not retract that to me sounds like a bad switch which we offer with the part #LC144214.

view full answer...

Answer 2

I was unable to find your order number but I assume you have the Replacement Electric Jack Switch with Harness #LC387874 for your Lippert Components High-Speed Power Stabilizer Jack #LC298707 as this jack will have black and red wires that the switch…

view full answer...

Answer 3

Thanks for reaching out! Since you have the 4951KS model MaxxFan roof vent you'll need the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS. The circuit board might look slightly different as far as the pieces…

view full answer...

Answer 4

The MaxxAir FanMate vent cover Item #MA00-955001 is going to be just a little taller but the louvred end tapers in and it does not come with the screen which is Item #MA00-955202. 25" long x 18-1/8" wide x 10-1/4" tall. The MaxxAir II…

view full answer...

Answer 5

For a protective cover for your roof vents I recommend the MaxxAir II RV and Trailer Roof Vent Cover w/ EZClip - Black #MA86JR. This is cover uses a high-density polyethylene construction that is UV resistant and will also protect your roof vent from…

view full answer...

Answer 6

The model number for fans such as the MaxxAir MaxxFan Mini Roof Vent, #MA00-04401M is listed on the upper side of the assembly itself. Please see the attached image. You will best identify this by opening the vent and climbing on top of the RV.…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

It sounds like your MaxxFan may need a new circuit board. Typically, when customers had similar issues they were able to replace the circuit board and their fan return back to normal operation. You can use Replacement Printed Circuit Board…

view full answer...

Answer 11

On oil bath hubs the seals are different than standard grease seals. The correct replacement for what you have is #91030. Unitized oil seals like this have a part that stays fixed and a part that rotates with the hub for optimum leak protection. I…

view full answer...

Answer 12

The correct circuit board for your MaxxAir MaxxFan 4951KS fan is the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS. It also works with The MaxxAir MaxxFan 4751KS and 4761KS models as well.

view full answer...