Replacement Velcro Strips for Bed Rails on a TruXedo Tonneau Cover on a 2004 Ford Ranger

Question

Question:

I already purchased a replacement vinyl cover for my 2004 Ford Ranger with a 6 ft. bed. The velcro that is in the rail is worn out and the vinyl is not holding on to the rail, Do you sell the rail side strips of the velcro? Truxport is a good product. I had my original vinyl 8 years. I have the truxport lo that rolls up. thank you

asked by: Greg H

0

Expert Reply:

We do have the TruXedo Velcro strips that fit in the rails. We have an 80 inch long by 1-5/16 inch wide set of 2, # TX1115174. For longer beds we have # TX1115173 which is 90 inches long.

We no longer have the Replacement Velcro Adhesive Kit for older style covers that have adhesive backing strips.

expert reply by: Michael H

0

Answer 1

While we do not carry the Tonno Pro brand of tonneau covers, I do still have a potential solution for you. Check out the: -Replacement TruXedo Shur-Bond Velcro Brand Fastener #TX1115174. This Velcro strip measures 1-5/16" wide, and 80"…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Hey Joshua, the Aries Grille Guard part #AA3056 that you referenced that fits your 2005 Ford F-150 comes with the needed install hardware so you would not need to get that separately. If somehow you misplaced it we do have it as a replacement part…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...