Can the CE Smith Heavy Duty Vertical Bunk Brackets Be Used on an I-Beam

Question

Question:

Can your Heavy Duty Vertical Bunk Brackets be used on a boat lift I-beam? My I-beam is 4inch high and 3inch wide. The U-bolts you sell seem wide enough but they are only 3inch long. Do you sell longer U-bolts? Sounds like I would need 5.

asked by: Charles G

0

Expert Reply:

Yes, the CE Smith Heavy Duty, Vertical Bunk Brackets # CE10161GA-2 can be used on an I-beam as long as you have compatible U-bolts that fit your beam and the brackets.

The CE Smith Heavy Duty, Vertical Bunk Brackets # CE10161GA-2 will require two 1/2" diameter U-bolts for installation, unfortunately we do not have any U-bolts that fit the height that you are needing. We only have one U-bolt long enough and it has a diameter other than 1/2". So you would need to source compatible U-bolts.

expert reply by: Scott S

0

Answer 1

The Fulton Outboard Motor Lock, #FOML0127, is a universal fit item designed to fit as many motors as possible. It should fit as long as your Yamaha motors have swivel handles that are used to tighten the mounting bolts that secure the motor.

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Can the CE Smith Heavy Duty Vertical Bunk Brackets Be Used on an I-Beam

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching