Best Hitch Receiver for a 2013 VW Jetta TDI Sportswagen

Question

Question:

Hey there I was wondering if you guys were able to get an eco hitch for my 2013 golf wagon tdi with a 1 1/4” reciever? I see you guys have a 2” reciever. Thanks!

asked by: Nick K

0

Expert Reply:

I have a solution for you but you do not want a 1-1/4" hitch if you have the option to install a 2" like the EcoHitch item # 306-X7284. It has a different installation method that will hang down below your rear bumper. 2" hitch's have a higher capacity and a much wider range of options to choose from when it comes to accessories. The Ecohitch is custom fit and bolts to your 2013 Jetta TDI with included hardware. It's installation method behind the rear bumper will leave only the 2" x 2" receiver visible. To use 1-1/4" accessories with this hitch you will want to use the 2" to 1-1/4" Trailer Hitch Receiver item # e63YR. This sleeve will allow you to use all your 1-1/4" accessories and not reduce the hitch's capacity.

The reducer sleeve does not work on towing. If you are going to be towing you will need the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver lock with keys, hitch cover, and a storage case.

If you need a wiring harness to control your trailer or accessories lighting functions you will want the Wiring Harness Kit # C59496.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

From the research I did it looks like your 2010 Subaru Forester has a 2,400 lb towing capacity. You will need to check your owners manual to verify this as well though. The trailer hitches we offer for your vehicle have capacities that are quite a…

view full answer...

Answer 3

The EcoHitch Hidden Trailer Hitch Receiver #306-X7284 is identical to the X7284 you saw on the TorkLift site. If you look at the picture Torklift is using, you will see underneath that the actual design may vary. They often use stock images, which…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...