HappiJac Custom Tie Downs For A 2014 Ford F-150 W/ A 6-1/2 Foot Bed

Question

Question:

need set of anchor plates 182860 ? or 182870 please confirm so i can order from you

asked by: Stephen J

0

Expert Reply:

According to Lippert, the correct kit for your 2014 Ford F-150 is the:

-HappiJac Truck-Mounted Camper Tie-Downs # LC182860.

This kit includes 2 Front support braces, 2 Front brackets and anchors, 2 Rear brackets and anchors, and the mounting hardware for istallation.

expert reply by: Bryce D

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 6

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 9

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...