Does the Draw-Tite DT52GR Hitch Fit the 2022 Hyundai Kona N?

Question

Question:

Hello. Which hitch will work for the 2022 Hyundai Kona N. Please be careful as the N is very different from the N line. Thank you in advance.

asked by: Nikola R

0

Expert Reply:

Based on your concern I messaged the hitch manufacturer. I just heard back from my rep at Draw-Tite and he confirmed that their Draw-Tite Trailer Hitch Receiver item # DT52GR does not fit the N model of the 2022 Hyundai Kona. Instead, we have the Curt # C87DR as a confirmed fit.

expert reply by: Jerred H

0

Answer 1

I think maybe our fitguide is causing a bit of confusion, but the Draw Tite hitch part #DT52GR is a confirmed fit for your 2022 Hyundai Kona Electric SEL. This fits the electric and non electric models which the way our fitguide is configured causes…

view full answer...

Answer 2

Yes, the Curt Trailer Hitch Receiver #C87DR does fit your 2022 Hyundai Kona N-Line. Additionally, if you're needing wiring the correct part is Wiring Harness #C59236.

view full answer...

Answer 3

The biggest difference between a frame mounted hitch and a factory accessory (lifestyle) hitch that is on your 2021 Kia Seltos, is a hitch such as the Curt Trailer Class 1 Hitch Receiver Item #C65FR provides a maximum gross tow rating of up to 2,000…

view full answer...

Answer 4

I checked with Curt and their trailer wiring harness part #C99KR is a confirmed fit for the 2023 Hyundai Kona ev as it is a fit for all models.

view full answer...

Answer 5

Yes, we do offer locks for the Saris Bones EX 2 Bike Rack part #SAR83FR. The 8' Cable Lock and lock Loop for Saris Trunk Mounted Bike Racks part #SAR52FR is a two in one. It locks the bikes to the rack and then the rack to the vehicle. The rack…

view full answer...

Answer 6

We haven't had the chance to install either the Curt #C11529 trailer hitch on the 2018 Hyundai Kona, so I'm not going to have a precise measurement for you at this time. That said, from what I can tell, based on the installation photos, this…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...