Lippert Solera Regal Style Awning Arm Head Replacement Covers In Black

Question

Question:

Do you have this in black?

asked by: John

0

Expert Reply:

Yes, we have the Replacement Cover for Solera Awnings # LC643923. This is the regal style in black for the idler side of your awning. We also have the Replacment Cover # LC643922 for the drive side of the awing.

The Rear Cover # LC643921 will fit on either the the drive or idler head.

expert reply by: Bud M

0

Answer 1

In order to separate two awning head covers such as the Solera Awning Plain Drive Head Front Cover part #LC289560 and the Solera Awning Plain Drive Head Back Cover part #LC289561 you'll need to remove the screws which are accessed from the back…

view full answer...

Answer 2

For your Solera Awning, you can use the Replacement Cover for Solera Awnings #LC643923 for the front, and the Replacement Cover for Solera Awning #LC643921 for the back. I have included a couple of videos for you to check out as well.

view full answer...

Answer 3

We have idler head covers for the front and back of the Solera awnings. The part #LC289560 that you referenced is a drive head front cover though. For an idler head you'd want the part #LC643923 for the front and #LC289567 for the rear.

view full answer...

Answer 4

To remove the front cover #LC643923 from your Solera Awning there are indeed 2 screws that need to be removed. If you look at the back f the idler head unit you can see the locations where the screws reside that you need to remove. I have attached a…

view full answer...

Answer 5

Though it can vary, the model number is typically somewhere around on the right hand side once the awning is extended. If you still cannot located it, you can also contact the trailer manufacturer with your VIN and they should be able to get you the…

view full answer...

Answer 6

The install of the Replacement Cover for Solera Awnings #LC643923 is pretty simple. It's basically held on with just two screws that you'll easily be able to locate on the old head you have now. Since this cover does not come with screws…

view full answer...

Answer 7

Meg, for your Lippert Solera 2000 series awning you can use the Replacement Front Cover for Lippert Edge Awnings #LC32NJ for the front and #LC43UD for the rear to replace your damaged cover. Also, if by cap you're meaning the manual override…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...