Fitting Larger Rhino Rack Pioneer Platform to Leer Topper with Thule Tracks

Question

Question:

I need to fit a bigger platform on my leer topper with factory installed Thule tracks. Is there a setup that will let me run one of the 56” wide pioneer platforms?

asked by: J S

0

Expert Reply:

You could use the Rhino Rack Pioneer Platform # RR35TB which is 60 by 49 inch and then for feet that would attach it to your Thule roof rack tracks all you'd need is two sets of the Rhino Rack RLTP Legs part # RLTP and you'd be set.

expert reply by: Jameson C

0

Answer 1

It sounds like you're looking for a complete roof rack system where the tracks are 54" to put on a camper shell that's on your 2013 Nissan Titan. If that's the case, you're looking for the Rhino-Rack Aero Bar…

view full answer...

Answer 2

For a great cargo basket that will definitely fit your Rhino-Rack HD Crossbars on your #Y01-120B-NT, I recommend the Aluminum Roof Mounted Cargo Basket - 44" Long x 39" Wide x 7" Deep #288-09200. Since the compatible…

view full answer...

Answer 3

We've actually asked Rhino Rack this in the past and they told us that the Pioneer Platforms like the part #RR35TB can attach directly to the Rhino Rack feet part #RLTP-3.

view full answer...

Answer 4

Yes, the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells #Y01-120B will fit the Thule tracks you have on your Century topper.

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 10

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 11

Hi Larry, So we have a couple bumpers that may work, though each is 96 inches long. They can be cut to length though, and the difference is their width, as one is 3" wide and the other 4" wide to fit different size bumpers: - Pre-Drilled…

view full answer...

Answer 12

In order to attach the Rhino-Rack Pioneer Platform to a set of crossbars you would need the kit that comes with universal mounts which is part #RR42114BF for 48" long x 37" wide or part #RR42115BF for 58" long x 47" wide. This…

view full answer...

Fitting Larger Rhino Rack Pioneer Platform to Leer Topper with Thule Tracks

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching