Using Chains/Ratchet Binders with Brophy Stake Pocket Tie Downs # TL1B

Question

Question:

Can these tie downs be used with chains and ratchet binders? All the photos and video for these tie downs show web straps used. My situation is with Grade 70 chains for tying down a tractor. Thank you

asked by: Mike W

0

Expert Reply:

Yes. I went ahead and reached out to my tech at Brophy, and he said that as long as you are within the weight capacity of the Brophy Stake Pocket Tie-Down Anchor # TL1B, you can use chains/ratchet binders. It is important to note that each tie-down has a working load limit of 4,000 pounds.

expert reply by: Bob C

0

Answer 1

The usable dimensions of the Brophy Stake Pocket Tie Down Anchor part #TL2B are 7-3/8 inches from the center of the pin hole to the plate that sits on top of the anchor, the width is 3-1/2 inches and the depth of it is 1-1/2 inches. This is…

view full answer...

Answer 2

I have a solution for you, but the Buyers Products Coupler Latch Lock is not available as a "keyed alike" lock. I recommend using the etrailer Trailer Coupler Latch Lock - 7/8" Span - 1/4" Diameter - Chrome - Keyed…

view full answer...

Answer 3

So I went out to the warehouse and measured the stake pocket anchor #TL2B and from the lip to the top of the pin hole is right at 6-3/4". As long as your stake pocket is really only 6" deep these will work just fine for you.

view full answer...

Answer 4

If the inner width of your flatbed trailer's stake pockets are 3-1/2" then you're going to want the Brophy Stake Pocket Tie Down Anchor item #TL2B you were looking at. The dimensions are 8-1/4" tall x 3-1/2"…

view full answer...

Answer 5

It is plastic. The ComeUp UW-5000si Trailer Winch item #CU645010 is a light duty winch so it's housing and base are made of plastic. I attached a picture below that will show you the base. I've also linked an installation video that…

view full answer...

Answer 6

Yes it does; per the manufacturer the correct Draw-Tite trailer hitch that fits your 2023 Hyundai Sonata hybrid is the following: - Draw-Tite Sportframe Trailer Hitch Receiver #DT74MR

view full answer...

Answer 7

It sounds like the left side may have a bad ground in the system or a loose ground. I would check over the complete wiring system and make sure all grounds have a good metal contact and no rust. Also check the wires to make sure the protective…

view full answer...

Answer 8

I have a different option for you, but there is no such adapter for raising and lowering your Bulldog 12,000lb trailer jack with an electric impact. The only non-manual option offered is the Bulldog Powered-Drive Kit for Single-Speed Jacks w/…

view full answer...

Answer 9

The Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 #HSSF are not ideal if the camper won't be resting on them. The amount of torque if the camper is not resting on them may cause them to deform or the bed…

view full answer...

Answer 10

For a stake pocket that you could weld to the side of your trailer that would allow you to make your own walls for the trailer you could use the part #HW03-080. The inner dimensions of the stake pocket are 3-1/2" (w) x 1-9/16" (deep). This…

view full answer...

Using Chains/Ratchet Binders with Brophy Stake Pocket Tie Downs # TL1B

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching