Can Hollywood Racks Sport Rider SE be Used in 2-1/2 Inch Hitch With Adapter

Question

Question:

Can I use an adapter to fit a class V hitch that is 2-1/2?

asked by: Greg B

0

Expert Reply:

You can indeed use an adapter for your 2-1/2 inch hitch to mount the Hollywood Racks Sport Rider SE. In fact, Hollywood Racks makes an adapter specifically for this situation that works with this bike rack, so what you will need is the following:

- Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes # HLY84FR

- Hollywood Racks Hitch Receiver Reducer Sleeve - 2-1/2" to 2" # HRHA-2

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 3

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...

Answer 4

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 5

I have a solution for you. Here at Etrailer, we strongly discourage using wheel-mounted bike racks like the Kuat NV 2.0 #NV22B for bikes with fenders. Mounting wheels with fenders can cause the fenders to crack or become damaged, especially with the…

view full answer...

Answer 6

The RockyMounts MonoRail bike rack you'd looked at, part #RKY10004 is a great bike rack, but it wouldn't work well with bikes that have fenders like your Aventon Aventure Fat tire ebikes. The front fender would prevent the bike retaining hook…

view full answer...

Answer 7

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Yes, it does. The Hollywood Racks LED Light Bar item #HLY54RR is wired for a 4-way but comes with an adapter that will plug into a 7-way like yours to power the lights.

view full answer...

Answer 10

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For an e-bike rack for your Letric XP step thru bikes at the rear of an RV the Swagman E-Spec part #S94FR would be a great choice as it's rated for the rougher ride quality at the rear of RVs, has the higher weight capacity needed at 60 lbs per…

view full answer...