Brackets Needed To Mount Flexco Pull-Out Steps On A 2018 Forest River Wildwood Travel Trailer

Question

Question:

2018 Forest River Wildwood 171 RB XL - has a 25 1/4 inch bracket, need two step model, and dont find it in your chart. Spacers on the SMFP-2120? Currently has a one-step model, but we are in our late sixties...

asked by: Mark M

1

Helpful Expert Reply:

The Flexco Manual Pull-Out Steps for RVs # SMFP-2120 does not come with spacers but you can purchase some Outriggers # LC301704 separately to help mount your new steps. These outriggers will bolt onto your 2018 Forest River Wildwood 171 RBXL travel trailer's frame to give you the correctly spaced mounting brackets for these steps.

expert reply by: Kevin C

1

Answer 1

Yes, the outriggers #LC301704 can be used to install the Flexco Manual Pull Out Steps #SMFP-2120 on your Rockwood trailer.

view full answer...

Answer 2

Since you are going from 1 step to 2 steps for your manual pull out step setup on the 2016 Salem Cruise Lite the brackets of the 2 step systems are going to be wider. We do not carry a 2 step manual pull out step that would fit the 25" mounting…

view full answer...

Answer 3

To replace the single step Flexco step assembly on your Forest River Wolf Pup 16BHS Trailer, I recommend taking a look at the Flexco Manual Pull-Out Steps #SMFP-2100. This double step assembly features 9 inch deep, pull-out steps with a non-slip…

view full answer...

Answer 4

Most single step RV steps are either 20 inches wide or 24 inches wide. So depending on which you have now you could use the part #SMFP-2120 for a 20 inch wide step or part #SMFP-2100 for a 24 inch wide step.

view full answer...

Answer 5

For your 2016 Rockwood Forest River Freedom 1950 Pop-Up Camper, I recommend looking at the Flexco Manual Pull-Out Steps #SMFP-2120. This 2-step unit features 20 inch wide steps with a non-slip surface and a 1-1/2 inch wide strip of grip tape on the…

view full answer...

Answer 6

It sounds like your RV has the outriggers or something similar. For new outriggers we have #LC301704 you can use.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Brackets Needed To Mount Flexco Pull-Out Steps On A 2018 Forest River Wildwood Travel Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching