Compatibility with Furrion Vision S # FOS05TASF with Pre-Wired 2021 Coachman Apex UltraLite

Question

Question:

MY TRAILER wasnt LISTED,ITS A2021 coachman aPEX utralite 553rl.its pre wired for a back up camera jut wanted to no if this is the right wireless camera for my rv.If not can you email me the correct one.

asked by: Leonard B

0

Expert Reply:

Yes, the Furrion Vision S # FOS05TASF works with your pre-wired 2021 Coachman Apex Ultralite 553RL is pre-wired trailer.

expert reply by: Bob C

0

Answer 1

In regard to the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision part #FOS05TASF, the diameter of the ball on the suction cup mount (Replacement Suction Cup Mount for Furrion Vision S Wireless RV Backup Camera System part #FR79SR)…

view full answer...

Answer 2

It sounds like you're asking about the torque spec for the castle nut on your 3,500 lb axle. There is no specific torque rating when installing the castle nut on any axle. You want to run the nut down until there is no side to side play in…

view full answer...

Answer 3

We do have what you need, but since your 2022 Winnebago 2529RG is prewired for the Voyager system you will not want to use the Voyager WiSight 2.0 Wireless RV Backup Camera System w/ Night Vision #ASA57YR that you were looking at. Because you will…

view full answer...

Answer 4

Based on the photo you provided your trailer is already setup for Furrion camera systems like the Furrion Vision S Wireless RV Backup Camera System w/ Night Vision #FOS05TASF. To get your camera to power on while driving you will simply need to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Compatibility with Furrion Vision S # FOS05TASF with Pre-Wired 2021 Coachman Apex UltraLite

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching