Replacement Bushings For Rear Leaf Springs On A 2010 Hino 268

Question

Question:

2010 hino 268 leaf spring bushings. I want the exact matching with the pins

asked by: Celestine A

1

Helpful Expert Reply:

We do have bushings of various sizes, but most bushings have a 9/16" inner diameter and a 11/16" outer diameter. The Nylon Bushing - 9/16" Inner Diameter, 11/16" Outer Diameter - 1-3/4" Long, part # TRBU11566, is this bushing.

I did some online research and I was unable to find any information about the size of the bushings in the leaf springs on your 2010 Hino 268. You can reach out to Hino directly to get the parts you need or you can take some measurements of your existing leaf springs and bushings. The leaf springs will need to measured when not tensioned in order to get an accurate measurement. I can possibly help you get replacement bushings even if provided with only your axle model and length of leaf springs.

I have included a product description link below.

expert reply by: Mark Smith

1

Answer 1

The best way to lift your Jayco Eagle is called an over/under conversion kit, which moves your trailer's leaf springs to the top of your axle and lifts your trailer approximately the same amount as your axle's diameter plus the height…

view full answer...

Answer 2

I never recommend using grease with Nylon Bushings #TRBU11566. The grease can trap dirt which will cause the nylon to become damaged easier. And the chemicals in different greases can cause the nylon bushings to break down. If you want to use…

view full answer...

Answer 3

Bushings do not always have to be used. Springs typically have bushings or they will use wet bolts depending on which part of the suspension system it is but not always. The bushings limit the wear on the suspension components. There are just…

view full answer...

Answer 4

We have an article to assist with checking your brake magnets like you are stating. The resistance will go down because the brake magnets are connected in parallel. Since the voltage doesn't change, the amperage draw needs to increase to power…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Replacement Bushings For Rear Leaf Springs On A 2010 Hino 268

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching