What Gauge Wire Does Triple LED Trailer Tail Light # CE44VR Use

Question

Question:

Ready to install on our motorhome. Want to use WAGO connectors, so need to know the wire size please. Thanks

asked by: Philip L

0

Expert Reply:

The Triple LED Trailer Tail Light # CE44VR that you referenced uses 18 gauge wire.

expert reply by: Jameson C

0

Answer 1

The LED Trailer Tail Light #328-003-81LM1 is listed as being for the driver's side because that is traditionally where the license plate is on trailers, but you can use this light on the right (passenger's) side if that's…

view full answer...

Answer 2

I've linked to a diagram showing the dimensions of the Command #CE44VR trailer lamp. We don't have a video completed as of yet, but when we do, it'll appear on the website.

view full answer...

Answer 3

The Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens Item #CE44VR is sold individually. If you needed two you'd need to order a quantity of 2. I attached a picture of a similar Command Electronics from the back…

view full answer...

Answer 4

If your RV currently has incandescent lights and you're going to be adding the Triple LED #CE44VR to the mix then you will most likely need to add resistors like the Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2 #DI34ZR to…

view full answer...

Answer 5

The Command Electronics LED Trailer Tail Light - Rectangular - White Base - Red Lens - Driver Side #328-003-81LM1 and Passenger side #328-003-81M1 are different in that the driver's side has the license plate mount bracket integrated as well as…

view full answer...

Answer 6

I reached out to Command Electronics for their Passenger Side LED Trailer Tail Light #328-003-81BM1. They informed me the running lights will pull around 19mA while the tail light will pull 26mA. We also have the Driver Side #328-003-81LBM1 with the…

view full answer...

Answer 7

You could certainly reverse the position of the lamps by installing the #328-003-81LBM1 lamp on the passenger side and the #328-003-81BM1 lamp on the driver's side. Both lamps wire the same way, the white wire is the ground connection, the red is…

view full answer...

Answer 8

It certainly sounds as if you're getting an insufficient ground connection. I would definitely take a dime sized area around the hole for the ground screw down to bare metal, then install a star washer between the frame and the ring terminal on…

view full answer...

Answer 9

We do have a version of the Optronics RV Tail Light - Stop, Tail, Turn - Rectangle - Red Lens - Passenger Side - Black Base #RVSTB60 with a white base. The #RVSTL60 is the exact same light, just with a white base.

view full answer...

Answer 10

I have a few options for you to replace the Bargman 30-91-010 Tail Lights. There isn't a direct LED replacement. The Bargman Trailer Tail Light part #30-92-001 and part #30-92-003 are direct replacements but they are incandescent. You could…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Gauge Wire Does Triple LED Trailer Tail Light # CE44VR Use

Product Page this Question was Asked From

Continue Researching