Is There An LED Replacement for the Bargman 30-91-010 Trailer Tail Lights

Question

Question:

Is there an led replacement for both passenger and driver side to this model?

asked by: Darrin C

0

Expert Reply:

I have a few options for you to replace the Bargman 30-91-010 Tail Lights. There isn't a direct LED replacement. The Bargman Trailer Tail Light part # 30-92-001 and part # 30-92-003 are direct replacements but they are incandescent. You could change out the 1157 bulbs to LED or you could just go with the LED Trailer Tail Light part # 328-003-81LBM1 and part # 328-003-81BM1 which are just a slightly different size.

expert reply by: Conner L

0

Answer 1

To determine the correct cover, you will need to measure the vent opening. The most common openings are 14 1/4" x 14 1/4", and have vents that are 14" x 14". After you make your measurements, you will need to determine what type…

view full answer...

Answer 2

There are three types of hinges for replacement roof vents: 3 point, 4 point, and continuous. Replacement #BV0534-00 has a closed round hinge, which is continuous. It sounds like you need either a continuous hinge that is not closed such as…

view full answer...

Answer 3

In order to determine the correct replacement lid for your 1996 Dutchman Thor, you are going to need to measure your actual vent. The most common size vents are 14-1/4" x 14-1/4" so you'll want to verify that yours is a standard vent.…

view full answer...

Answer 4

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 5

The closest LED tail light we carry to Bargman #30-92-002 that you referenced is part #328-003-81M1 for the passenger's side and #328-003-81LM1 for the driver's side. They're fairly close in size but don't have the reverse light…

view full answer...

Answer 6

I would run a set of e-tracks down the length of the floor of your trailer like part #E19148 (5 foot section), and then use the wheel nets like part #EM58523 to secure the wheels of your cars to the tracks. Check out the install videos I attached as…

view full answer...

Answer 7

Yes, you just have to remove the old lights, match the wires and mount the new ones. Please note, that it is usually not a good idea to mix LEDs and incandescent lights, so if you have have side markers or other lights on the trailer, make sure you…

view full answer...

Answer 8

We don't offer a flat surface mount lamp that would include the license plate lamp, but the Diamond Group #DG52721PB would provide stop/turn/taillight and the reverse lamp. For a license plate lamp, you can mount something like #OPT77FR above the…

view full answer...

Answer 9

Having your trailer be level is really important for tongue weight accuracy, so it is prudent and safe to put a block under the etrailer Tongue Weight Scale #e99044. Just make sure the block and scale are on level ground and stable; also chock the…

view full answer...

Answer 10

It would be technically possible to measure trailer tongue weight with a hanging scale assuming you had a way to put it at the exact height to attach it to your trailer as it sits level and the weight capacity was high enough. We have floor scales…

view full answer...

Answer 11

The LED Trailer Tail Light #328-003-81LM1 is listed as being for the driver's side because that is traditionally where the license plate is on trailers, but you can use this light on the right (passenger's) side if that's where your…

view full answer...

Answer 12

You could certainly reverse the position of the lamps by installing the #328-003-81LBM1 lamp on the passenger side and the #328-003-81BM1 lamp on the driver's side. Both lamps wire the same way, the white wire is the ground connection, the red is…

view full answer...

Is There An LED Replacement for the Bargman 30-91-010 Trailer Tail Lights

Products Referenced in This Question

Continue Researching