Recommended Front Mount Trailer Hitch for 2008 Toyota Tundra

Question

Question:

Front hitch model for 2008 Toyota Tundra 4x4?

asked by: Greg G

0

Expert Reply:

The Draw-Tite Front Mount Trailer Hitch Receiver part # 65080 is what I recommend for a 2008 Toyota Tundra. It offers a bolt-on fit with no drilling required for installation. It fits both 4x4 and 4x2 models. It will work great for winches, bike racks, snow plows, and many more. It has a 500 lb vertical load rating and 9,000 lb line pull.

Please note, the skid shield will need to be removed or modified for re-installation.

expert reply by: Conner L

0

Answer 1

Yes, we do have a front mount hitch for a 2022 Toyota Tundra. It is the Draw-Tite Front Mount Trailer Hitch item #65080. This hitch has a 2" x 2" receiver and a 500 lbs vertical load limit.

view full answer...

Answer 2

I had our warehouse measure each of the front mount trailer hitch receivers you mentioned, and the dimensions are as follows. The Curt #31408 measures 32-3/4" long x 8-3/4" wide, the Draw-Tite #65080 measures 36-3/4" long x…

view full answer...

Answer 3

I was able to get the measurements you were looking for of the Draw-Tite front mount hitch that fits your 2020 Toyota Tundra, which is the following: - Draw-Tite Front Mount Trailer Hitch Receiver #65080 The hitch is similar to the Curt #31198 in…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Recommended Front Mount Trailer Hitch for 2008 Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching