How Much Does the BedSlide 1000 Classic Truck Bed Slide Tray 1,000 Lbs Weigh

Question

Question:

How much does this weigh? Looking to see how much payload I would have after installing this in my truck.

asked by: Dan M

0

Expert Reply:

The BedSlide 1000 Classic Truck Bed Slide Tray - 1,000 Lbs part # BE24ER weighs around 200 lbs.

expert reply by: Conner L

0

Answer 1

I attached a picture that shows all of the dimensions of the MORryde Sliding Tray for RV Cargo Compartment #MR93FR. This picture is actually in our product pictures already but it's buried pretty far down on the list of them.

view full answer...

Answer 2

The tray of the MORryde RV Cargo Sliding Tray #MR93FR has a 1.57" clearance so you will need the Height Adjustment Kit #MR34VR if the cargo compartment lip in your 2022 Grand Design Solitude 390RK-R Fifth Wheel Trailer is taller.

view full answer...

Answer 3

You have already pointed out the differences with the number of bearings and the other difference is capacity rating. The CargoGlide 1500XL Sliding Tray for Trucks - Heavy Duty - 1,500 lbs - Steel Frame - 8" Rail #CG1500XL-9548 has 36…

view full answer...

Answer 4

If the Bearing Buddies are not the correct size or are not driven in straight then they can fall off due to the centrifugal force when the wheels spin. To ensure you get the right size you can go by the bearing numbers of the hubs or measure the hole…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

How Much Does the BedSlide 1000 Classic Truck Bed Slide Tray 1,000 Lbs Weigh

Product Page this Question was Asked From

Continue Researching