Is The Lippert Anti-Billowing Kit A Compatible Replacement For The Dometic Anti-Billowing Kit

Question

Question:

is this interchangeable with DOMETIC 312418000U Anti-Billow Kit, Hardware, Black ?

asked by: Steve J

0

Expert Reply:

I spoke with the manufacturer, Lippert, and was told that the Lippert Anti-Billowing Kit for Solera Slide Topper Awnings # LC78FR is only going to be compatible with Solera slide out awnings so if you're awning is Solera branded you'll be fine using this product. If you have a Dometic awning then you'll need to use the Dometic branded Anti-Billow Kit.

expert reply by: Kevin C

0

Answer 1

Please note the attached instructions. The Lippert Anti-Billowing Kit for Solera Slide Topper Awnings, #LC78FR should be installed on the end of the awning that is closest to the front of the unit. 1. Make sure awning is fully retracted. 2. Place the…

view full answer...

Answer 2

If the fabric on your Solera RV Slide-Out Awning - 6'7" Wide - 48" Projection - White #LCV000163285 is laying loose with no tension you've most likely lost the required amount of tension on your tension springs. You'll want to…

view full answer...

Answer 3

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 4

I have a solution for you, but my contact over at Lippert tells me that you won't be able to replace just those casings on Solera Slide-Out Topper. The parts you need are the Replacement Idler Head and Roll Tube for Solera RV Slide-Out Awning -…

view full answer...

Answer 5

The Lippert Components Anti-Billowing Kit for Solera Slide Topper Awnings - Black #LC78FR is designed to fit right over the slide awning roller as pictured. The inside diameter of the arm is 2.545 inches according to my tech contact at Lippert.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...