Replacement Wheel Stud for Dexter 8-213-5UC1-EZ 5200 lb Idler Hub

Question

Question:

Hi Im looking for replacement pressed studs to fit the following hub on my trailer. Do you have any? or know the part number? thanks Dexter Trailer Idler Hub Assembly for 5,200-lb E-Z Lube Axles - 6 on 5-1/2 Item # 8-213-5UC1-EZ

asked by: Greg L

0

Expert Reply:

According to my Dexter Axle representative, the correct drive-in 1/2 inch wheel stud for your # 8-213-5UC1-EZ idler hub is part # 7-122.

expert reply by: Mike L

0

Answer 1

Assuming you are meaning replacing the entire hub, you will first need to remove the oil bath cap to access the spindle nut. There will be a cotter key holding the nut on, or a clip which will need to be removed next. After that remove the nut and…

view full answer...

Answer 2

The Trailer Hub Wheel Stud part #7-122 which measures 1/2" diameter x 2" long with a .62" spline length would be the best match option we have for you.

view full answer...

Answer 3

You should be able to replace the wheel stud, but you'll need to drive the stripped stud out and get the measurements shown in the provided diagram in order to locate the correct replacement. You'll need a drift punch that is smaller in…

view full answer...

Answer 4

I would be happy to help you find the correct replacement wheel studs for your hubs, but unfortunately the part number shown in your picture are for the brake assemblies and not the hub. To determine the correct replacement wheel studs you will need…

view full answer...

Answer 5

We have the part #7-150 which is just a tiny bit longer by 3/32 of an inch but aside from that matches the #7-122 but is galvanized.

view full answer...

Answer 6

I was not able to track down specific information regarding the studs for your existing hubs, but if you have a 5,200 to 6,000 pound hub with the 6 on 5-1/2 inch bolt pattern you mentioned, you will likely need a 1/2 inch drive-in stud. If your…

view full answer...

Answer 7

I checked with Dexter and was able to verify the correct studs for the Dexter Trailer Hub and Drum 42656. Per Dexter the correct replacement is the 2" long stud, which is the following part number: - Trailer Hub Wheel Stud - Drive In - 1/2"…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Replacement Wheel Stud for Dexter 8-213-5UC1-EZ 5200 lb Idler Hub

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching